P&C Stuff
- Thread starter jabberwoki
- Start date
3baygarage
Well-known member
Cool find on the hammer.
A pair of old ratchets. 1/2” and 3/8”. I believe 18 tooth and 16 tooth.
A pair of old ratchets. 1/2” and 3/8”. I believe 18 tooth and 16 tooth.
Beerhippie
Well-known member
I had no idea P&C made junque-drawer hammers!
Outlawmws
Well-known member
Same
bmwrd0
Well-known member
The end was not too kind to P&C.
Beerhippie
Well-known member
Part of a nice haul today.
If this fills a hole for anyone, let me know. Shipping and it's yours. Ball detents (there's one for the cross bar) still work.
Outlawmws
Well-known member
Part of a nice haul today.
If this fills a hole for anyone, let me know. Shipping and it's yours. Ball detents (there's one for the cross bar) still work.
I'm interested - PM coming.
Beerhippie
Well-known member
Claimed!
d42jeep
Well-known member
I found this P&C 706 screwdriver at yesterday’s estate sale and got rid of the rust. 
-Don
-DonOldtuleguy
Well-known member
- Joined
- Nov 4, 2017
- Messages
- 10,450
Outlawmws
Well-known member
OTC, is that an exposed gear version?
Oldtuleguy
Well-known member
- Joined
- Nov 4, 2017
- Messages
- 10,450
Yup, just like the old 3/8 and 1/2 versions
Outlawmws
Well-known member
They made a 9209 18/19" long too I have the one my dad had, probably from the Navy.
Oldtuleguy
Well-known member
- Joined
- Nov 4, 2017
- Messages
- 10,450
Nice! You have a pic? I think that's a 3/4
Last edited:
Outlawmws
Well-known member
I do from a 2012 post when I refinished a dead/dying box to make up a set that was semi portable (the whole mess weighs 50 lbs...
The no finish extension and one of the smaller sockets were from my Dad's tools; the rest were acquisitions...
Oldtuleguy
Well-known member
- Joined
- Nov 4, 2017
- Messages
- 10,450
GemState10ER
Active member
- Joined
- Jul 5, 2025
- Messages
- 29
Nice finds! I have the 3/4 one, still on hunt for the matching “plug” or even any older USA to go with it.Cool find on the hammer.
A pair of old ratchets. 1/2” and 3/8”. I believe 18 tooth and 16 tooth.
GemState10ER
Active member
- Joined
- Jul 5, 2025
- Messages
- 29
Looks like everyone’s finding some cool stuff! Hope this summer is a good one! Here’s a visually appealing set I’ve put together from about every source available(some in here 
) *sockets are mostly speed master*
) *sockets are mostly speed master*GemState10ER
Active member
- Joined
- Jul 5, 2025
- Messages
- 29
Loaded up the kids and drove an hour away to get this off marketplace! Funny thing is he thought the hex drives were rare and it was listed as “hex drive socket set”. Wish it had more P&C sockets but my first 1” 3/16, and a craftsman L handle. Outside is “crinkle” but inside is smooth. 
OP
jabberwoki
Well-known member
r_olson_06
Well-known member
Now that's a wall!
d42jeep
Well-known member
I think that is a WF-17 extension. This is what it shows in my WF list.
“WF-17 3/8 Drive 5" Extension”
“WF-17 3/8 Drive 5" Extension”
Thanks, fixed.
This 3/4" drive set was way back in my tool storage pile. An oddball set that I had completely forgot about. Obviously a early set but can't find it in any of the catalogs. Tools are consistent in markings and used very little.
Last edited:
r_olson_06
Well-known member
Picked up these at the swap meeting in a pile of rusted cast iron tools. Didn't know they were p&c until I was able to get them home and cleaned up. The stamping and wrench style looks early!
3baygarage
Well-known member
Very nice
So nice they stamped it twice. Good find.Picked up these at the swap meeting in a pile of rusted cast iron tools. Didn't know they were p&c until I was able to get them home and cleaned up. The stamping and wrench style looks early!
Outlawmws
Well-known member
Picked DBE this on Fri:
d42jeep
Well-known member
I found this P&C combo at yesterday’s estate sale. I‘m not sure what the remaining coating is but if it was chrome plated it is the worst I‘ve seen. 
-Don
-Don
Outlawmws
Well-known member
d42jeep
Well-known member
What is left is not dull like cad. It could be very poorly plated nickel. I’ll either run it through the evaporust or let the next owner figure it out, since I generally pass along any P&C I find to others.
-Don
-Don
GemState10ER
Active member
- Joined
- Jul 5, 2025
- Messages
- 29
Luckily the plain steel under is good quality and cleans up nice!I found this P&C combo at yesterday’s estate sale. I‘m not sure what the remaining coating is but if it was chrome plated it is the worst I‘ve seen.
-Don
Oregon rock crusher
Well-known member
Here is the longest 1/2" P&C extension I've seen. Picked up with some Plomb pieces at a swap meet over the weekend in Coburg. Not many vendors but there were a few things to pick through. No marking on the extension other than P&C but it shows up in the late 20's to early 30's as a 6015. Just a tick under 18" long. Ed.
Attachments
r_olson_06
Well-known member
Picked this up at an auction. I seen the pebble and my heart sank thinking it was Plomb. I flipped it over and saw P&C and thought that is a pretty good pick up as well.
Nice find, The P&C is a much better looking 4way than the Plomb.Picked this up at an auction. I seen the pebble and my heart sank thinking it was Plomb. I flipped it over and saw P&C and thought that is a pretty good pick up as well.
r_olson_06
Well-known member
Good to know. Is the Plomb pebbled?
Here are a couple of early P&C items I picked up at the Tahoe flea this morning. A 1" cold chisel and a pair of lineman's pliers.
-Don
Well, I almost matched Don's decade-old Tahoe find, with my finds from last weekend.
